Solar energy

Solar panel production in winter: impressive facts and honest figures in Ukraine

solar panel output in winter illustration for Solar panel output

The production of solar panels does not stop in winter: photovoltaic modules generate electricity both in frost and in cloudy weather. However, a short daylight hours, low sun position, frequent clouds and snow cover significantly reduce the result compared to summer. For a Ukrainian home solar power plant, the winter months usually provide only a small part of the annual generation, and the difference between a clear and cloudy day can be tenfold. To correctly assess the capabilities of the station, it is important to calculate not the peak power of the panels, but the expected output in kWh, taking into account the region, roof orientation, tilt angle, shading and system losses.

Do solar panels work in winter?

solar panel output in winter illustration for Solar panel output

A solar panel converts light, not heat, into electricity. Therefore, low temperatures in themselves do not hinder generation. On the contrary, with the same amount of sunlight, a cold photovoltaic module works more efficiently than a very hot summer one.

The main winter problem is not frost, but a lack of solar radiation. In Ukraine, in December the sun is low above the horizon, the day lasts much shorter than in June, and cloud cover is often dense and long. Because of this, less energy reaches the surface of the modules.

The panels generate radiation from two components:

– direct light, coming directly from the sun;
– scattered light, which passes through clouds and is reflected by the atmosphere, ground, or snow.

On a cloudy day, the direct component is almost absent, but the scattered light allows the station to operate. The power may be only a small fraction of the nominal. For example, a 10 kW array of panels is not required to produce 10 kW even at noon: the nominal is determined under standard laboratory conditions, which are rare in winter.

Why does frost sometimes increase power?

The nominal power of the module is specified at a solar cell temperature of 25 °C. The data sheet also states the temperature coefficient of power. For common silicon modules, it is often in the range of approximately −0.3% to −0.4% for each degree of increase in cell temperature above 25 °C.

If the cells are at a temperature of around 0 °C in clear, frosty weather, their instantaneous efficiency at the same illuminance can be approximately 7.5–10% higher than at 25 °C. Calculation for the coefficient −0.35%/°C:

25 × 0.35% = 8.75%.

This does not mean that in winter the station will produce more energy per day than in summer. The temperature gain does not compensate for the short day and weaker insolation. But on a clear frosty afternoon, properly installed panels can indeed show high instantaneous power.

How much do solar panels produce in winter in Ukraine?

There is no single indicator for the entire country. Generation in Uzhhorod, Kyiv, Kharkiv, and Odessa differs due to climate, latitude, cloudiness, and duration of snow cover. Even two neighboring stations may have different results due to roof orientation or shade from trees.

For preliminary assessment, use specific output — the number of kilowatt-hours obtained from one kilowatt of installed capacity:

Specific output = generation per period ÷ panel power.

An approximate winter range for an unshaded stationary solar power plant, oriented close to the south and installed at a suitable angle, might look like this:

| Part of Ukraine | Estimated production for December–February, kWh from 1 kW of panels | Estimated generation of a 10 kW solar power plant for the winter |
|—|—:|—:|
| West and North | 70–110 | 700–1100 kWh |
| Central regions | 85–125 | 850–1250 kWh |
| South | 100–150 | 1000–1500 kWh |
| East and Southeast | 90–140 | 900–1400 kWh |

This is not a guaranteed forecast, but a practical range for initial planning. In an isolated cloudy and snowy winter, the result may be lower, and with a large number of clear days - higher. Panels on an east or west slope, local shadows and prolonged snow cover also reduce the output.

Which month is the weakest?

Ukrainian solar power plants usually generate the least amount of electricity in December. The reasons are obvious:

– winter solstice and the shortest daylight hours;
– low altitude of the sun;
– frequent continuous cloudiness;
– fog and precipitation;
– snow accumulation on the modules is possible.

READ ALSO:  Solar Panels for Remote Sites: How to Choose the Best 2026

In January, the length of the day gradually increases, but the result depends heavily on the weather and snow. February is usually more productive: the sun rises higher, daylight becomes longer, and there may be more clear periods.

For a rough estimate, the specific generation of an optimally oriented station can be within the following broad limits:

| Month | Estimated output, kWh from 1 kW of panels |
|—|—:|
| December | 15–35 |
| January | 20–40 |
| February | 40–70 |

The values cannot be mechanically applied to every facility. For example, a 10 kW plant with a specific output of 25 kWh/kW would give:

10 kW × 25 kWh/kW = 250 kWh per month.

The average daily result will be approximately:

250 ÷ 31 = 8.1 kWh per day.

However, this is only an arithmetic average. On a cloudy day, the station can produce 1–3 kWh, and on a clear day, several times more. That is why average monthly figures are not suitable for guaranteeing autonomy on a specific day.

Solar panel output in winter: what determines the result

Geographic location

Southern regions tend to receive more winter solar radiation than northern regions. But latitude alone does not explain everything. Local cloudiness, fog, relief, and the number of clear days are important.

In mountainous areas, the opposite scenario is possible. A valley may remain in fog for a long time, while an object above the cloud layer receives bright sunlight. Therefore, an accurate assessment should be made based on the coordinates of a specific house, and not just the name of the area.

Panel orientation

For maximum annual and winter production in Ukraine, the direction to the south is most often chosen. A small deviation to the southeast or southwest is usually not critical, but changes the generation profile:

– southeast gives more energy in the morning;
– southwest — after lunch;
– the east-west system stretches generation throughout the day, but its winter output is usually lower than that of a southern system of the same capacity;
– northern orientation is especially disadvantageous in winter.

If electricity is needed mainly in the evening, the southwestern array is sometimes more useful for self-consumption, although its total output may be slightly lower.

Tilt angle

In winter, the sun is low, so a steeper tilt allows the rays to fall on the modules at a closer to a right angle. For stationary home solar power plants, a compromise tilt is often used, designed for the whole year. If winter generation is the priority, an angle of about 50–70° may be appropriate, but the optimal value depends on latitude, orientation and design.

The steep angle has two additional advantages:

1. snow slides off the surface more easily;
2. modules retain less dirt and water.

However, excessive increase in the angle can reduce summer and total annual production. For rooftop solar power plants, wind load and strength of fasteners must also be taken into account. It is not worth changing the design without engineering calculations.

Shadow from trees, buildings and chimneys

Shadows are longer in winter than in summer. A tree or neighboring house that is not a problem in June may shade the panels for several hours in December.

Partial shading is dangerous not only by reducing the illuminated area. In a conventional string, the modules are connected in series, so a shaded element can limit the current of the entire circuit. Bypass diodes reduce the problem, but do not eliminate losses completely.

For complex roof geometry, the following can help:

– distribution of modules into separate MPPT inputs;
– power optimizers;
– microinverters;
– moving panels from an area that is regularly shaded.

Electronics do not create additional sunlight, so their benefits must be weighed against the cost and complexity of the system.

Inverter, cable and battery losses

The power of the DC modules is not equal to the useful energy at the output of the system. Some of the energy is lost:

– during the conversion of direct current to alternating current;
– in cables, contacts and protective equipment;
– due to mismatch of characteristics of individual panels;
– in case of contamination or shading;
– during charging and discharging of the battery;
– due to the internal consumption of the inverter and control system.

READ ALSO:  Solar battery charge controller: MPPT or PWM — how to choose the right one

For a grid-connected station, it is important to distinguish between the output of the inverter and the energy actually used by the house. For a hybrid system, it is additionally necessary to separate the energy directed to the battery from that which was later returned to the consumers.

Snow on the panels: benefits, disadvantages and safe cleaning

Clean snow around the station reflects light well. This can increase the illuminance of the modules, especially in clear weather and in double-sided panels if the back surface is exposed to reflected radiation. However, snow directly on the front surface usually sharply reduces generation.

A thin transparent layer sometimes lets some light through, but thick or wet snow can practically block the operation. Uneven coverage creates partial shading: the top of the module is already clear, while the bottom is still covered by a snowdrift.

Do I need to clean the panels?

The decision depends on accessibility, angle of inclination and weather forecast. If the modules are located on a steep roof, the snow often melts on its own after the sun comes out. Manual cleaning for the sake of a few winter kilowatt hours is not worth the risk of falling or damaging the glass.

If the above-ground structure is safely accessible, a soft brush or a special scraper without metal edges can be used. Do not:

– stand or lean on modules;
– beat off the ice with a hard object;
– pouring hot water on a cold glass;
– use abrasives;
– working on a slippery roof without professional insurance;
– damage cables and connectors with tools.

A sharp temperature drop can damage the glass, and scratches reduce light transmission. If the panels are covered with ice, it is safer to wait for it to melt naturally.

How to calculate the winter generation of your solar power plant

The most reliable preliminary calculation is made using many years of meteorological data for precise coordinates. In the solar potential calculator, you need to specify:

– installation location;
– array power in kW;
– azimuth;
– angle of inclination;
– type of installation;
– estimated system losses.

The result will show the expected monthly generation, but will not predict the weather of a particular winter. The data should be taken as a multi-year average.

Calculation example for a 6 kW station

Let's assume the estimated specific output in December is 24 kWh from 1 kW of panels. Then:

6 × 24 = 144 kWh for December.

Average daily value:

144 ÷ 31 = 4.65 kWh per day.

If the house consumes 15 kWh daily, the December solar power plant will cover on average:

4.65 ÷ 15 × 100% = 31% of daily intake.

In fact, the proportion of direct self-consumption will depend on the operating hours of the devices. If most of the electricity is consumed in the evening, without a battery, part of the daytime generation may not be used directly in the house.

Why you can't multiply the rated power by daylight hours

A common mistake is to calculate like this: the station is 10 kW, the day lasts 8 hours, so it will produce 80 kWh. This calculation is incorrect, because the panels do not operate at their rated power throughout the day.

In the morning and evening, the light is weak, at noon the power depends on the clouds, the angle of incidence of the rays and the temperature. The real graph on a clear day resembles a curve with a maximum near sunny noon. On a cloudy day it can be low and uneven.

Will winter generation be enough for an autonomous house?

For full autonomy, it is not enough to know the average monthly production. The system must be tested for the worst realistic period - several cloudy days in a row. A large battery does not solve the problem of lack of energy if the panels cannot charge it.

First, the daily consumption balance is drawn up:

| Device | Power | Operating time | Consumption |
|—|—:|—:|—:|
| Refrigerator | depends on the cycle of operation | during the day | determined by measuring |
| Lighting 60 W | 60 W | 5 h | 0.30 kWh |
| Laptop 65 W | 65 W | 6 hours 0.39 kWh |
| Pump 800 W | 800 W | 0.5 h | 0.40 kWh |
| Electric kettle 2 kW | 2000 W | 15 min | 0.50 kWh |

Energy is calculated using the formula:

kWh = power in kW × operating time in hours.

READ ALSO:  Solar panels for the home without permits: how to stop praying for an outlet and start earning from the sun

Particularly large consumers in winter are electric heating, boilers, underfloor heating, electric stoves and electric car charging. For example, a 2 kW heater will use 20 kWh in 10 hours - more than a small home solar power plant typically produces on a cloudy winter day.

A practical stand-alone or backup system often requires:

– reduction of non-critical loads;
– shifting the operation of the boiler, washing machine and pump to sunny hours;
– battery for evening and night consumption;
– a backup energy source for long cloudy periods;
– automatic load control.

Battery capacity should be evaluated not only in ampere-hours, but in useful kWh, taking into account the permissible depth of discharge, efficiency, and temperature conditions.

How to increase winter production without unnecessary costs

Remove shading

The best results are often not from buying additional modules, but from eliminating the shade. It is worth checking the area in December and January around morning, noon and afternoon. Pruning branches must be safe, legal and not harming trees or the surrounding area.

Shift consumption to the middle of the day

In winter, the useful generation window is short. It is advisable to start the boiler, washing machine and dishwasher when the station is already producing a surplus. This increases the share of self-consumption without increasing the battery capacity.

Control can be implemented by timers, power control relays or an energy management system. At the same time, it is necessary to take into account wiring limitations and not turn on too many powerful devices at the same time.

Monitor the operation of each MPPT or string

A sharp drop in generation is not always caused by weather. Possible causes include:

– the machine is turned off;
– inverter error;
– damaged connector;
– a problem with one of the strings;
– local shading;
– snow only on part of the massif.

It is worth comparing days with similar weather conditions and separate inverter inputs. If one of two identically oriented strings consistently produces significantly less, the system should be checked by a qualified professional.

Do not overcharge panels without checking the inverter

Adding modules can improve winter generation, but the array must meet the allowable parameters of the inverter. Check the maximum DC voltage, MPPT operating range, allowable input current and maximum power.

The open circuit voltage is especially important: it increases in cold weather. If the string is designed without temperature correction, the permissible inverter voltage may be exceeded in winter. Reconfiguration should be performed by the designer or installer, not the owner by arbitrarily connecting the panels.

Common myths and misconceptions

«The panels don't work in the cold.». They work when exposed to light. Cold even improves the electrical performance of the modules under the same light conditions.

«Under the clouds, generation is zero.». Diffused light provides output, although it may be very low.

«Snow always increases generation.». Snow around the modules can reflect light, but the snow layer on the front surface mainly creates losses.

«For the forecast, power in kW is enough.». Kilowatts indicate nominal power, while kilowatt-hours indicate actual energy produced. Without insolation data, the former does not determine the monthly result.

«The average daily generation is sufficient to calculate autonomy.». The average hides the dark periods. The autonomous system is checked by the deficit days, not just by the monthly amount.

«The bigger the battery, the better the system.». An overcharged battery may remain undercharged in winter. First, a balance of generation and consumption is needed, and only then the choice of capacity.

Practical guidelines for the owner of a solar power plant

Solar panels in winter in Ukraine should be perceived as a useful but uneven source of energy. For a grid station, winter generation (Incomplete: max_output_tokens)

Additional solar panel output in winter illustration for Solar panel output in winter: impressive facts and honest figures

Solar generation equipment

Choose the necessary equipment with an official warranty in our store.

Leave a Reply

Your email address will not be published. Required fields are marked *